RF-Max Digimax 210 Instrukcja Użytkownika Pobierz pdf (Strona 6)

110

Tel 0870 990 9000 Fax 01332 830551 Web www.keene.co.uk

Keene Electronics Catalogue 2005 Tel 0870 990 9000 Fax 01332 830551 Web www.keene.co.uk

Appliance module

Simplicity itself, just unplug the device you want

controlled, plug this into the socket then plug the device

back in. Set the X10 address as needed and you now

have instant X10 control. The module can switch on or

off an appliance of up to 13 amps, ideal for kettles, fans,

heaters, lamps, etc. The appliance module has an added

feature in that if the item connected to it is desired to

be manually controlled without having to send a signal

to it, the appliance module will switch to the 'on'

position by a simple turning 'off' and 'on' of the

appliance. The module itself will only turn off if a signal

is sent to it.Max load 16A (resistive) 1A (inductive).

[AM12U] £24.99

Multi-buy deal on 5 appliance modules £105.00

Wired appliance module

Essentially an AM12 appliance module with the

plug part chopped off. This version is more

compact allowing for direct connection to your

chosen appliance. Ideal for discreet (built) in

applications where you'd rather not have the

AM12 module in the wall socket, and also for

appliances that are hard wired.

[AM12W] £24.99

X10 receivers (things that act on receiving an X10 command)

Lamp module

Gives you instant X10 control of any plug in lamp. Plugs

into a 13 amp socket and will switch on/off lamps plug-

ged into the module's standard 3 pin socket. In addition

it can dim/brighten (standard tungsten or halogen

filament bulbs only, NOT fluorescent). More than one

lamp may be connected to a lamp module but can not

be controlled independently. If a lamp connected to the

module is desired to be manually rather than X10

controlled, the lamp module will switch to the 'on'

position by a simple turning 'off' and 'on' of the lamp

switch. The module itself will only turn off if a signal is

sent to it. In some cases, where lights have transformers

or their own dimmer systems, there may be a conflict with X10 dimmer

commands in which case an appliance module would be more appro-

priate. Load 40W (minimum) 300W (max) incandescent lamps only.

[LM12U] £24.99

Multi-buy deal on 5 lamp modules £105.00

Wired lamp module

Essentially an LM12 lamp module with the plug

part chopped off. This version is more compact

allowing for direct connection to your lights and

can be built into ceilings and partitioned walls

etc. Identical to the LM12U in specification and

operation

[LM12W] £24.99

X10 compatible low voltage transformer

For those of you that would like to have X10

control of your existing low voltage (12V)

halogen lighting we've sourced some high

quality replacement transformers. They're

fully compatible with X10 and once fitted

you can use an LD10 or LW10 for X10 on off

and dim/brighten commands. The transformers are very well made

with low operating noise and are self resetting with inbuilt short

circuit and overload protection. For ease of connection each unit has

two pairs of input terminals and two pairs of output terminals. Output

rating 105VA (say 5 x 20W bulbs)

[P105] £12.99

Our telephone order hotline is 0870 990 9000. Order any time – no answering machines, talk to real

people 24 hours a day, 365 days a year

Appliance wall switch

The wall appliance switch is the same size and

fits in the same way as a standard UK single

gang appliance switch. It is designed to replace

existing appliance switches and to offer control

over those appliances through our signalling

system (for instance, control a washing machine

that at present is plugged into a switched wall

socket). The wall appliance switch is also a

suitable command tool for fluorescent lights,

which the wall dimmer switch can not handle. It

can control appliances of up to 10 amps and is specifically designed to

be a double pole single throw switch, that is, it switches both the live

and the neutral. (Most light switches have only the live or neutral

present but not both and so our switch cannot be used under those

circumstances - if in doubt you should consult an electrician.) More

than one appliance may be connected to a wall appliance switch but

they can not be controlled independently. The wall appliance switch

receives signals via the electricity supply whether the switch itself is on

or off and has a light to indicate whether it is on or off. However, if

the appliance has a switch then it must be in the 'on' position for our

wall appliance switch to be able to control it. As with all X10

equipment, the wall appliance switch can be simply programmed with

an address so that when signals are sent to it, it can react. Once the

switch is fitted, the address can be changed without removing the

switch. Max load 10A (resistive) 3A (inductive).

[AW10U] £34.99

Wall dimmer switch

Just replace your standard wall light switch

with this wall dimmer switch for instant X10

control. It is the same size and fits in the

same way as a standard UK single gang light

switch, and is designed to provide control

over the lights through X10 signalling. In

addition to turning 'on' and 'off', it can dim

down or up. The wall dimmer switch receives

signals via the electricity supply whether the

switch itself is on or off. However, if the light

fitting has a switch then it must be in the 'on' position. As with all

X10 equipment, the wall dimmer switch can be simply programmed

with an address so that when signals are sent to it, it can react to

appropriate commands. Once the switch is fitted, the address can be

changed without having to remove the switch.

Notes: For use only with standard tungsten or halogen lamps, NOT

fluorescent. Does not support two-way switching. More than one light

may be connected to a wall dimmer switch but multiple lights will not

be independently controllable. Please see our notes on low voltage

lighting. Load 60W (minimum) 300W (max) incandescent lamps only.

[LW10U] £34.99

Plug in filter

If a particular appliance causes interference that

affects your X10 commands, simply unplug it and

plug in again via this filter. It prevents any unwanted

"noise" from the appliance entering the ring main.

[FM10] £29.99

X10 bayonet lamp module

Probably the easiest way to achieve X10

control of a lamp - simply remove the bulb,

plug in the module and then replace the bulb -

that's it! The lamp will now respond to on/off

X10 commands (not dim or brighten) and can

still be operated with your conventional light

switch. Very nifty. Note, the light switch must

be left "on" before X10 can assume control. 150W max incandescent

tungsten lamps only. 70mm long.

[LM15EB] £19.99

Multi-buy deal on 5 bayonet fit lamp modules £110.00

1 2 3 4 5 6 7 8

Komentarze do niniejszej Instrukcji

Brak uwag

RF-Max Digimax 210 Instrukcja Użytkownika Strona 6

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Termostaty RF-Max Digimax 210